Updated November 2026
An all grain home brewing equipment setup lets you turn crushed malt into wort from scratch, controlling every step from mash temperature to final boil. This guide walks you through the core pieces, how to arrange them on brew day, and the mistakes that trip up most first-time all-grain brewers. By the end, you will have a workable layout you can build with used or budget gear.
Start With the Core Vessels
Every all-grain system needs three vessels: a mash tun to hold grain and hot water, a boil kettle, and a fermenter. Many brewers begin with a single cooler-style mash tun with a false bottom or a braided stainless steel filter, paired with a kettle of at least 8 gallons for 5-gallon batches. If you are shopping secondhand, check that the kettle has no pitting or dents at the weld seams, since those spots harbor bacteria. For a broader look at what to buy first, see What Equipment Needed for Home Brewing? A Starter Checklist.
Shopping for one? See our guide: 3 Best All Grain Home Brewing Equipment Picks for Every Setup (2026).
Plan Your Heat Source and Layout
Your heat source determines how you lay out the brew day. Gas burners and electric elements both work, but they draw different amounts of power and need different clearances. Electric setups typically require a dedicated circuit, so confirm your home’s capacity with a licensed electrician before wiring anything. Arrange the mash tun, kettle and a sink or hose connection in a line or triangle so you can move hot liquid with minimal lifting. For a deeper look at heating options, read Home Brewing Heating Equipment: A Step-by-Step Guide for Beginners. 5 Best All-Clad HA1 Cookware Set Options for Home Cooks (2026) goes further into this.
Add the Support Gear
Beyond vessels and heat, you need tools that measure and move liquid. Set up the following before your first mash:
- A thermometer or temperature probe rated for mash and boil ranges
- A hydrometer and a clean sample jar for gravity readings
- A wort chiller, either immersion or counterflow, to drop wort temperature quickly
- Food-grade tubing and a pump or gravity siphon for transfers
- A sanitizer and a dedicated scrub brush
- A grain mill or a pre-crushed malt supplier
Before you use any of these pieces, sanitize them thoroughly. The steps are covered in Sanitizing Home Brewing Equipment: A Step-by-Step Guide for Beginners.
Run a Dry Test Before Brew Day
Fill the mash tun with 3 gallons of water and heat it to your target mash temperature, usually between 148°F and 158°F. Check that your thermometer holds steady, that the valve drains fully, and that the kettle reaches a rolling boil without scorching the bottom. A dry run exposes leaks and awkward connections while the stakes are low. Note any spots where you need to reposition hoses or add a stand.
Common Mistakes
- Skipping a temperature check before adding grain, which leads to inconsistent mash efficiency
- Underestimating boil volume, so the final batch comes out short of your target
- Placing the fermenter too close to heat sources, which can raise fermentation temperature
- Using unsanitized tubing or chiller coils, which invites off-flavors
- Buying a kettle too small for the batch size you plan to brew
Recommended Gear
A braided stainless steel false bottom makes the mash tun easier to drain clean. View on Amazon
A digital instant-read thermometer helps you hit mash temperature without guessing. View on Amazon
Food-grade silicone tubing keeps wort transfers simple and sanitary. View on Amazon
FAQ
How many vessels do I need for all-grain brewing?
You need at least three: a mash tun, a boil kettle and a fermenter. Some brewers combine mash and boil tasks in one vessel, but that approach requires a different workflow.
Can I set up an all-grain system on a small budget?
Yes. Many brewers start with used kettles and a cooler mash tun, then upgrade over time. Check Used Home Brewing Equipment for Sale: 3 Best Picks for Starter Brewers (2026) for secondhand ideas.
Do I need electricity for all-grain brewing?
Not necessarily. Propane burners work well outdoors, though electric systems offer more consistent temperature control. Consult a licensed electrician before adding any new high-draw circuit at home.
Conclusion
A solid all grain home brewing equipment setup comes down to three vessels, a reliable heat source, and a few measuring and transfer tools arranged for an easy workflow. Run a dry test before your first brew day to catch leaks and layout problems early. With the setup in place, your attention can shift to the recipe and the process.
