Updated November 2026
Brewing beer equipment commercial setups look very different from a home kitchen, but the core job is the same: heat water, extract sugars, ferment, package, and keep everything clean. This guide walks you through how to plan a commercial-style system, which pieces matter most at each scale, and where a flea-market mindset still saves money as you grow.
Step 1: Decide Your Batch Size and Production Goal
Your batch size drives every other choice. A system sized for 1 barrel (31 US gallons) behaves very differently from one built for 7 barrels. Start by estimating how much beer you need per month, then work backward to a batch size you can brew at least two or three times a week. Smaller brewhouses are easier to keep clean and let you test recipes without tying up large volumes.
Shopping for one? See our guide: 5 Best Equipment for Beer Brewing for Home Brewers in 2026.
Many new commercial brewers start with a brewhouse sized for about 1 to 3 barrels and add fermenters as sales grow. If you are still learning process control, the principles in What Equipment Do I Need for Home Brewing Beer? A Starter Guide translate well to a small pilot system.
Step 2: Plan the Brewhouse Vessels
A basic commercial brewhouse has a mash tun, a lauter tun (or a combined mash/lauter vessel), a brew kettle, and a whirlpool. Some systems use a single vessel for mashing and boiling to save floor space. Heating method matters too: steam, direct-fired gas, and electric elements each have different installation requirements, and many jurisdictions require permits for gas and steam work. Check with your local building and fire authorities before you buy.
Key sizing rules
- Plan the kettle at roughly 1.2 to 1.5 times your target post-boil volume to allow for evaporation and trub loss.
- Match the mash tun to your grain bill. Heavier grain loads need more headspace.
- Use a whirlpool or hop-separation step if you plan to reduce trub going into fermenters.
Step 3: Choose Fermentation and Cold-Side Equipment
Fermenters are where most of your tank budget goes. Conical fermenters with cooling jackets give you control over yeast harvest and temperature, while cylindroconical and flat-bottom tanks are common in larger operations. Plan at least one tank per batch, plus a spare when you are scaling, so you can brew while another batch conditions. Glycol chillers or a glycol loop keep temperatures steady, and a properly sized chiller prevents off-flavors from temperature swings.
For a deeper look at fermentation hardware and its trade-offs, see Home Brewing Fermentation Equipment: A Step-by-Step Guide for Beginners.
Step 4: Set Up Packaging, Cleaning and Utilities
Packaging equipment includes kegs, a keg washer, a filler (for cans or bottles), and a carbonation system. Cleaning is a constant task, so plan for a CIP (clean-in-place) loop or a tank wash system, and make sure you have hot water, caustic and acid cleaners, and sanitizer on hand. Utilities such as water treatment, drainage, and compressed air are often underestimated. Get a plumber and an electrician involved early, and confirm that your building can handle the electrical load.
Sanitation is the most common failure point in small breweries. The step-by-step approach in Sanitizing Home Brewing Equipment: A Step-by-Step Guide for Beginners shows the sequence that carries over to larger systems.
Common mistakes
- Buying a brewhouse larger than your sales can support, then sitting on idle capital.
- Skipping a glycol plan and discovering later that fermentation temperatures swing too widely.
- Underestimating floor drainage and wastewater needs.
- Choosing gas or steam without checking permits and installation codes.
- Neglecting a maintenance schedule for pumps, seals and valves.
Recommended gear
For a commercial-style setup, a dependable digital thermometer and a calibrated hydrometer help you track gravity and temperature consistently across batches.
- A calibrated digital thermometer gives fast, repeatable readings during mashing and fermentation. View on Amazon
- A hydrometer set helps you confirm fermentation progress and calculate alcohol content. View on Amazon
- Food-grade sanitizer makes it easier to keep tanks and lines clean between batches. View on Amazon
FAQ
How much space does a small commercial brewhouse need?
Space depends on batch size, vessel layout and fermenter count, so there is no single figure. Plan for room to walk around every vessel, clear access for cleaning, and separate zones for milling, brewing, fermentation and packaging.
Do I need a license before installing brewing equipment?
Yes, in most places you need a brewing license, food-service or manufacturing permits, and inspections for gas, electrical and plumbing work. Requirements vary by country, state and city, so check with your local authorities and a licensed contractor before purchasing.
Is used equipment a good idea for commercial brewing?
Used vessels can save significant capital, but inspect welds, seals, jackets and controls carefully. Ask for maintenance records, and have a qualified technician check any gas or electrical components before use.
Conclusion
Commercial brewing equipment comes down to matching batch size to demand, then building out brewhouse, fermentation, packaging and cleaning in a sensible order. Plan utilities and permits early, because they often decide what is possible. Start with a system you can run cleanly, then expand as your sales and skills grow.
