Updated November 2026
Bars with kegerator built in let you pour draft beer from a cabinet that already holds the cooling, lines and taps in one unit. This guide walks you through choosing the right setup, planning the space, and getting a clean, cold pour from day one. Whether you are fitting a kegerator into a salvaged cabinet or buying a finished bar, the planning steps are the same.
Step 1: Decide Between a Factory Unit and a DIY Build
A factory bar with a built-in kegerator is the simplest route. The cooling system, collar and tap tower are engineered to work together, so you only need to plug it in and connect a gas line. A DIY build, usually based on a chest freezer or an old refrigerator conversion, gives you more control over size and style but requires more work. If you want the cabinet to match existing furniture, a DIY build is often worth the extra hours.
Shopping for one? See our guide: Built In Kegerator Outdoor: 5 Best Picks for Patio Bars (2026).
Step 2: Measure the Space and Plan Airflow
Kegerators need room to shed heat. Before you buy or build, measure the cabinet opening and leave clearance on the back and sides as the manufacturer specifies, commonly a few inches on each side for ventilation. Built-in installs that sit flush with no airflow will run longer, struggle to hold temperature, and can shorten the compressor’s life. Check the rated keg sizes against your cabinet depth so the keg, coupler and gas regulator all fit.
Step 3: Set Up the Gas, Lines and Tap Tower
Most built-in units use a CO2 cylinder inside or beside the cabinet. Plan the gas line route so it has no sharp bends or pinches. Run beer lines as short and straight as the layout allows, and keep the tap tower level so it does not drip back into the drip tray. Set your regulator to the pressure for the beer style you are serving, and let the system sit for a day before the first pour to settle the carbonation.
Tools and Parts Checklist
- Kegerator-rated refrigerator or purpose-built bar unit with a thermostat
- CO2 cylinder, regulator and gas line rated for draft beer
- Beer line, faucet, shank and coupler matched to your keg type
- Drip tray and a level for setting the tap tower
- Tape measure and a fine-tip marker for cabinet clearances
Step 4: Dial In Temperature and Carbonation
Most draft beer is served cold, and many guides suggest a serving temperature near the mid-30s to low-40s Fahrenheit, adjusted for style. Set the thermostat, wait for the keg to chill fully, then fine-tune pressure. Pouring too fast with a foamy result usually points to pressure or line length, not the cooler itself. Check the official manual of your unit for its recommended range before you adjust anything.
Common Mistakes
- Skipping ventilation clearance, which causes overheating and constant cycling.
- Using long, coiled beer lines without accounting for the extra resistance, leading to foam.
- Setting gas pressure high to speed up the pour instead of checking line length.
- Forgetting to clean the lines and faucet on a regular schedule.
- Building a cabinet too tight for the keg size you plan to use.
Recommended Gear
A quality beer line cleaning kit makes routine maintenance quicker, which keeps your pour clean over time. View on Amazon
A dual-gauge CO2 regulator lets you monitor cylinder pressure and serving pressure at a glance. View on Amazon
A stainless drip tray protects the cabinet floor from spills and is easy to rinse. View on Amazon
FAQ
Can I build a bar with a kegerator built in using an old refrigerator?
Yes, many home brewers convert an old refrigerator or chest freezer into a kegerator. Make sure the unit has a working thermostat and enough room for the keg, coupler and gas line.
How much ventilation does a built-in kegerator need?
Follow the clearances in the manufacturer’s manual, which typically call for space on the back and sides. Consult the official specifications for your exact model.
Should I clean my kegerator lines often?
Regular cleaning keeps beer tasting fresh and prevents buildup. Check your beer or equipment supplier’s guidance for your cleaning schedule and products.
Conclusion
Bars with kegerator built in work well when you plan the cabinet size, airflow and gas routing before you start. Take your time on temperature and line length, and the pour will be consistent. Keep the lines clean, and your setup will serve draft beer reliably for years.
