Updated November 2026

A corny keg fermenter conversion lets you turn a used 5-gallon Cornelius keg into a sealed, pressure-capable fermenter with a wide opening for cleaning and a tap for sampling. You will learn which keg to pick, what parts you need, how to modify the lid and dip tube, and how to test the finished vessel before it ever touches wort. The whole job takes an afternoon with basic hand tools if you plan it properly.

Choose the Right Keg and Confirm It Is Safe to Modify

Look for a 5-gallon ball-lock or pin-lock corny keg in good shape, with no deep dents, cracks at the seams, or heavy pitting inside. Ball-lock kegs are the most common choice for homebrewers because the lid fittings are easy to source. Before cutting anything, confirm the keg was never used for chemicals or cleaners, and check that the keg’s pressure rating is clearly stamped or documented. If you are unsure about the keg’s history or condition, consult a professional welder or a homebrew supplier before modifying it.

Shopping for one? See our guide: Corny Keg Conical Fermenter vs Plastic Bucket: Which Should You Choose?.

Gather the Parts and Tools

Most conversions use the same core list. Having everything on hand before you start prevents mid-job trips to the hardware store.

  • A ball-lock or pin-lock corny keg, cleaned and empty
  • A drill with a hole saw or a step bit sized for your fitting
  • A food-grade silicone or EPDM gasket that matches the lid
  • A bulkhead or thermowell fitting for the sample or airlock port
  • A pressure relief valve or spunding valve rated above your expected pressure
  • Teflon tape, food-safe lubricant, and a deburring tool
  • Sanitizer and a spray bottle for cleaning up metal shavings

Modify the Lid and Dip Tube

Most homebrewers use the keg’s existing lid and add a second port rather than replacing the whole top. Mark the port location on the lid, centering the hole away from the existing gas and liquid posts so the fitting does not interfere with the lid gasket. Drill slowly with light pressure and remove burrs immediately so the gasket seals cleanly. For sample or transfer use, the dip tube is usually left alone in a fermenter build, since you will move wort by gravity or pressure from the top. Test that the lid still seats evenly before you add any fittings.

Install the Fittings and Seal the Keg

Thread the bulkhead fitting through the hole and tighten it with the lock nut from inside. Wrap the threads with food-safe PTFE tape, then install the pressure relief valve or airlock adapter. Lubricate the lid gasket lightly with food-safe lubricant so it compresses evenly when you clamp it down.

Test the Vessel Before Brewing

Sanitize the keg, fill it with warm water, and close the lid. Pressurize it to a low, safe level using CO2 or your gas line, then apply soapy water to every fitting and seam. Bubbles mean a leak, so tighten or re-seat the part and retest. Hold the pressure for at least 30 minutes and watch the gauge. Once the vessel holds steady, empty it, sanitize it again, and it is ready for wort.

Common Mistakes

  • Drilling too fast, which causes the bit to grab and crack the lid rim.
  • Skipping the deburring step, which tears the gasket on the first seal.
  • Placing the port too close to the lid edge, where the clamp cannot seal properly.
  • Using a fitting or gasket not rated for your fermentation temperature.
  • Pressurizing a keg before the leak test is complete.
  • Step bit set: Makes clean, sized holes in thin stainless steel without tearing the metal. View on Amazon
  • Food-grade silicone gasket kit: Replaces worn lid seals and keeps the vessel airtight under pressure. View on Amazon
  • Bulkhead fitting for kegs: Gives you a sealed port for airlocks, sampling, or spunding valve installation. View on Amazon

FAQ

Can I use any old corny keg for a fermenter?

Only use kegs that are structurally sound, free of deep dents or corrosion, and have never held caustic or toxic substances. If you are unsure, use a new food-grade fermenter instead.

Do I need a spunding valve for a corny keg fermenter?

It is not required, but a spunding valve lets you hold pressure during fermentation for a more controlled carbonation level. A simple pressure relief valve is enough for basic fermentation.

How do I clean a corny keg fermenter after use?

Rinse out trub promptly, scrub the interior with a non-abrasive brush, then sanitize with a no-rinse sanitizer before the next batch. Always disassemble the lid and check the gasket for wear.

Conclusion

A well-built corny keg fermenter conversion gives you a sealed, pressure-ready vessel for a fraction of the cost of purpose-built equipment. Take your time with the drilling and the leak test, and the finished keg will serve you for years. Explore the related guides on this site for more ways to expand your homebrew setup.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our home brewing guides, checking product details against manufacturer specifications and owner feedback.