Updated November 2026
Converting a refrigerator into a kegerator means turning an ordinary fridge into a cold, pressurized draft station that pours beer from a keg through a tap on the door. With a used fridge, a collar kit and a CO2 setup, you can have a working home bar in a weekend. The main job is sealing the tap line, keeping the keg cold and setting the gas pressure correctly.
Choose the Right Refrigerator
Start with a fridge that has enough interior height for a corny keg with its gas and beer lines attached. Most standard kegs need roughly 17 to 18 inches of clearance, so check the inside height before you buy. A single-door fridge with a freezer on top usually works best because the freezer compartment can be removed or disabled. Avoid fridges with a heavily curved door, since the tap tower will not seat flat.
Shopping for one? See our guide: Turn Mini Fridge Into Kegerator: 6 Best Kits and Units Compared (2026).
A used fridge from a yard sale or a Craigslist listing is a classic flea-market find. Test that the compressor runs and holds temperature overnight before you invest in parts. If you are still comparing options, the article 5 Best Refrigerators for Kegerator Conversion Units for Home Bars (2026) covers models that tend to suit the job.
Prepare the Fridge and Install the Tap Tower
Remove the freezer shelves, the crisper drawers and the door bins that would block the keg. Set the thermostat to its coldest setting and let the fridge run empty for a few hours to confirm it reaches about 38 degrees Fahrenheit.
Next, drill the faucet hole through the door. Most people use a hole saw sized to the shank of the faucet, and they measure from the top of the door so the tap sits at a comfortable pouring height. Feed the shank through the hole, add the gasket and tighten the nut from inside. Route the beer line through the door gasket area and into the cabinet, using a grommet to protect the line from the door hinge.
- Measure the door and mark the tap location, usually near the handle side.
- Drill a pilot hole, then enlarge it with the correct hole saw.
- Install the shank, gasket and faucet nut from inside the door.
- Run the beer line down through the cabinet and fit it to the keg coupler.
- Attach the CO2 line to the regulator and check every fitting with soapy water.
Set Up Carbonation and Pressure
Connect the CO2 tank to a regulator, then run the gas line into the keg. For a beer at about 38 degrees, a common starting point is around 10 to 12 psi, though many brewers adjust based on the beer style and line length. Let the keg sit at serving pressure for several days before you expect a clean pour.
Line length controls the pour. Longer beer lines slow the flow and reduce foam. For a standard setup, a line of roughly 5 to 7 feet is typical, and the correct length depends on your pressure. If you are still choosing gas supply, Where to Fill CO2 Tanks for Kegerator: 6 Best Refill Options (2026) outlines where to get a tank filled.
Recommended gear
A hole saw kit sized for standard faucet shanks makes the door cut clean and reduces the chance of cracking the liner. Search for it with View on Amazon.
A dual-gauge CO2 regulator shows both tank and keg pressure, which helps you dial in serving pressure. Look for one with View on Amazon.
Keg wrench and coupler parts let you connect and disconnect kegs without losing gas. Find them with View on Amazon.
Common mistakes
- Skipping the door gasket, which lets cold air escape and causes frost on the tap.
- Setting the pressure too high for the line length, producing a foamy pour.
- Running the fridge without a dedicated outlet, which can trip breakers during compressor startup.
- Forgetting to tighten the faucet nut from inside, leading to leaks.
- Leaving the keg warm for a day after tapping, which causes foam until the beer chills.
FAQ
Do I need a special fridge to make a kegerator?
No, most standard single-door refrigerators with enough interior height will work. Check the inside clearance before buying, since a corny keg needs room for its connections.
What temperature should the kegerator run at?
Most beers are served around 38 degrees Fahrenheit. Set the thermostat to hold that temperature and verify it with a separate thermometer.
Can I use the freezer compartment for anything?
Most builders remove or disable the freezer to make room for the keg. If you keep it, make sure the keg still fits and the cooling stays even.
Conclusion
Converting a refrigerator into a kegerator comes down to choosing the right fridge, installing a sealed tap tower and setting the correct CO2 pressure. Take your time with the door cut and the line fittings, since those cause most problems. Once the pour runs clean, you have a home bar built from a secondhand fridge and a weekend of work.
