Updated November 2026
To convert fridge into kegerator, you need a fridge that can hold a keg, a way to keep the fridge running at a steady serving temperature, a gas line from a CO2 tank, and a tap tower mounted to the door or top. Once those pieces are in place, you can pour cold draft beer at home from a standard keg. The whole project is mostly about fitting and sealing, not electrical work.
Choose the Right Fridge and Check Its Fit
Most builders start with a used full-size or mini fridge from a flea market, yard sale, or secondhand appliance store. A single-door unit with a freezer compartment on top or a manual defrost works well, because you can remove the freezer shelves and make room for the keg. Measure the interior height and depth, then compare it with a Cornelius (corny) keg, which is roughly 23 inches tall and about 9 inches in diameter when you include the handle. Standard half-barrel kegs are much too large for most mini fridges.
Shopping for one? See our guide: 5 Best Kits to Convert Mini Fridge to Kegerators (2026).
Also confirm that the fridge still cools well. Plug it in, set it to its coldest setting, and check after several hours. If it struggles to get below about 40°F, the compressor or door seal may need attention before you go further.
Install the Collar, Thermostat, and Tap Tower
- Clean the fridge interior and remove all shelves, drawers, and the freezer tray if you plan to keep the keg standing.
- Drill a hole through the top or side wall for the gas and beer lines, using a rubber grommet to protect the wire and tubing.
- Mount a collar or tap tower bracket on the outside of the door at a height where you can reach the faucet comfortably.
- Run beer line from the keg coupler through the grommet and up to the faucet, keeping the run as short as practical.
- Connect the fridge to an external temperature controller. Many builders use a digital controller that plugs in between the wall outlet and the fridge, set to about 38°F for lager and 40°F to 42°F for ales.
Add the CO2 Line
Attach a regulator to your CO2 tank and run gas line into the fridge to the keg’s gas post. Set the regulator to a low working pressure to start, then adjust once you know your beer’s carbonation level. Check every connection with a spray of soapy water; bubbles mean a leak.
Dial In Carbonation and Pouring
Carbonation is the step most beginners rush. Set the regulator to about 10 to 12 psi, let the keg sit for several days at serving temperature, and then pour. If the beer foams, the line is too cold or the pressure is too high. If it tastes flat, raise the pressure slightly. Patience usually fixes both problems.
Common Mistakes to Avoid
- Skipping the temperature controller, which lets the fridge freeze the beer or run too warm.
- Using a beer line that is too long for your pressure, causing excessive foam.
- Forgetting to seal the grommet, which lets cold air escape and makes the compressor work harder.
- Overtightening fittings on the regulator and damaging the threads.
- Storing CO2 tanks lying down or in hot spaces; keep them upright and secured.
Recommended Gear
- Inkbird digital temperature controller: a plug-in controller that keeps the fridge at a steady set point for beer. View on Amazon
- Dual gauge CO2 regulator: shows both tank pressure and line pressure, which makes carbonation easier to manage. View on Amazon
- Beer line and keg coupler kit: includes the tubing and fittings needed to connect a corny keg to the tap. View on Amazon
For more on sizing and tap setups, see Keg Sizes for Kegerator: Which Size Fits Your Home Bar (2026) and Tower Cooler for Kegerator: How to Choose and Install One (Step-by-Step). If you prefer a ready-made option, Mini Fridge to Kegerator Conversion Kit: 6 Best Picks for Home Bars (2026) lists kits that save some of the fitting work.
FAQ
Can any fridge be converted into a kegerator?
Most single-door fridges with a freezer on top can be converted, provided the interior is tall enough for a keg. Check the height and make sure the compressor still reaches a cold temperature before starting.
What temperature should a kegerator run at?
Lagers are typically served around 38°F, while ales are often served between 40°F and 42°F. A plug-in temperature controller makes it easier to hold those settings.
Do I need a professional to install the gas line?
Basic gas line and fitting work is manageable for most DIYers, but if you are unsure about pressure settings or tank handling, consult a professional brewing supplier or appliance technician.
Conclusion
Converting a fridge into a kegerator comes down to choosing the right unit, mounting the tap tower, and getting the carbonation right. Take your time with the fitting and pressure settings, and you can pour good draft beer at home. Start with a used fridge and a simple setup, then upgrade parts as you learn what your beer needs.
