Updated November 2026

A kegerator CO2 pressure chart tells you what regulator pressure to run for a given beer style and serving temperature. Match those two numbers and your kegs will carbonate to the level you want without foaming at the tap. This guide walks through how to read the chart, set your regulator, and fix the most common pour problems.

How a CO2 Pressure Chart Works

Carbonation depends on two things: how much CO2 the beer holds and how cold it is. Colder beer absorbs more CO2 at the same pressure. A chart cross-references the target volumes of CO2 (for example, 2.4 volumes for a typical American lager) with the serving temperature to give a regulator PSI.

Most charts are built around a serving temperature of about 36 to 38°F. If your kegerator runs warmer or colder, the PSI number shifts. Always read the row for your actual temperature, not the one you guess.

Step-by-Step: Setting Your Regulator from the Chart

  1. Check the keg temperature with a fridge thermometer placed near the keg, not on the tower.
  2. Look up your beer style’s target volumes. Typical ranges: English ales 1.5 to 2.0, American ales 2.2 to 2.5, stouts 1.7 to 2.2, Belgian styles 2.5 to 3.0.
  3. Find the PSI where your target volume meets your serving temperature.
  4. Set the regulator to that PSI with the gas line disconnected from the keg, so you are reading the true setting.
  5. Reconnect and let the keg sit at that pressure for 24 to 48 hours before judging the pour.

Dialing In Pressure for Different Beer Styles

Light lagers and pilsners usually need higher carbonation for their crisp finish, while stouts and cask-style ales need less. Use the chart as a starting point, then adjust in small steps of 1 to 2 PSI.

Beer style Target volumes of CO2 Typical starting PSI at 38°F
English bitter or mild 1.5 to 1.9 Roughly 8 to 10
American pale ale or IPA 2.2 to 2.6 Roughly 11 to 13
Lager or pilsner 2.4 to 2.6 Roughly 11 to 13
Stout or porter 1.7 to 2.2 Roughly 9 to 11

These PSI values are rough starting points. Your line length, tap height and altitude all change the result, so treat the table as a first guess.

Adjusting for Foam and Flat Pours

If the beer pours foamy, the pressure is likely too high for your line length, or the beer is too warm. Drop the regulator 1 to 2 PSI, or lengthen the beer line. If the beer tastes flat after a few days, raise the pressure slightly and give it time to re-equilibrate. Avoid large jumps, since they make it hard to tell what changed.

For a deeper look at foam troubleshooting, see Foaming Beer from Kegerator? 6 Best Fixes and Parts to Stop It (2026).

Common Mistakes

  • Reading the chart for the wrong temperature. Measure the actual keg temperature every time.
  • Adjusting pressure while the gas line is connected to a keg that already has pressure built up.
  • Changing the setting and tasting the next day. Allow at least 24 hours before judging.
  • Using one PSI for every beer. Carbonation targets differ widely by style.
  • Ignoring line length. Long lines need less pressure to avoid foam; short lines need more.

A dual-gauge regulator lets you see both tank pressure and the outlet PSI you are actually setting. Owners often report it makes dialing in easier than a single gauge. View on Amazon

A fridge thermometer placed inside the kegerator gives you the real temperature that the chart depends on. View on Amazon

For setup details, see Co2 Bottle for Kegerator: A Step-by-Step Guide to Choosing and Connecting and 7 Best CO2 Regulators for Kegerator Picks Compared (2026).

FAQ

Can I use one PSI setting for every beer?

You can, but you will likely get flat or foamy results. Different styles need different carbonation levels, so adjust for each keg.

How long should I wait after changing the regulator?

Allow 24 to 48 hours for the beer to reach equilibrium at the new pressure before judging the pour.

Does altitude change the chart?

Yes. At higher elevations, atmospheric pressure is lower, so you may need to adjust the PSI slightly. Start from the chart and fine-tune by taste.

Conclusion

A kegerator CO2 pressure chart gives you a reliable starting PSI for each beer style at your serving temperature. Measure your temperature, set the regulator, and give the keg a day or two to settle. Small adjustments from there will get your pour right.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our home brewing guides, checking product details against manufacturer specifications and owner feedback.