Updated November 2026

A kegerator regulator not working properly can ruin a good keg in a single afternoon. Pressure either drops to nothing, climbs past what your beer can handle, or leaks from a fitting you were sure you tightened. Replacing the regulator is often the fastest fix, but only if you buy one that matches your tank threads, your working pressure range and the number of outputs you actually need. This list compares four CGA-320 CO2 regulators sold for home brewing and kegerator use. The selection criteria were specifications stated in each listing, brand reputation within the homebrew community, and patterns that owners tend to report, such as leak-free fittings, clear gauge markings and how well the safety valve holds up over time. We did not test these units ourselves.

Our top picks at a glance

  1. 1Keg regulator with 0-55 psi working pressure, single outputTOP CHOICEBest overallKeg regulator with 0-55 psi working pressure, single outputView on Amazon
  2. 2CGA-320 Beer Regulator with Safety Valve, dual outputBest for dual-keg setupsCGA-320 Beer Regulator with Safety Valve, dual outputView on Amazon
  3. 3CO2 Tank Regulator with 0-60 PSI working pressure, triple outputBest for multi-keg systemsCO2 Tank Regulator with 0-60 PSI working pressure, triple outputView on Amazon
  4. 40-60 PSI CO2 Tank Pressure Regulator, single output CGA-320Best budget pick0-60 PSI CO2 Tank Pressure Regulator, single output CGA-320View on Amazon

Our Top Picks

Product Best for Key feature
Keg regulator with 0-55 psi working pressure, single output Standard single-keg kegerators 5/16″ barb outlet and 0-55 psi working range
CGA-320 Beer Regulator with Safety Valve, dual output Two-tap or two-keg setups Y-shaped dual output with safety valve
CO2 Tank Regulator, triple output Multi-keg or multi-line systems Three outputs and 0-60 PSI working pressure
0-60 PSI CO2 Tank Pressure Regulator, single output Budget-minded single-keg users 0-60 PSI working range and 0-3000 PSI tank gauge

Keg regulator with 0-55 psi working pressure, single output

Keg regulator with 0-55 psi working pressure, 5/16" barb outlet, single output co2 tank pressure regulator for home brewing CO2 Regulator for Kegerator, Beer Regulator, CGA-320 C02 Regulator

Keg regulator with 0-55 psi working pressure, 5/16" barb outlet, single output co2 tank pressure regulator for home brewing CO2 Regulator for Kegerator, Beer Regulator, CGA-320 C02 Regulator

View on Amazon

Best for: Standard single-keg kegerators that need a dependable replacement.

This is a good fit for homebrewers with one keg and one tap who want a straightforward swap for a failing regulator. It uses the CGA-320 connection common on US CO2 cylinders.

Key specs

  • Working pressure: 0-55 psi
  • Outlet: 5/16″ barb
  • Single output
  • CGA-320 tank connection

Pros

  • Simple single-output design is easy to plumb and troubleshoot
  • The 0-55 psi range covers typical serving pressures for most beer styles
  • The 5/16″ barb fits the vinyl beer line most kegerator builds already use

Cons

  • Only one output, so it cannot feed a second keg
  • Owners often recommend checking the gauge against a second reading, since low-cost gauges can drift

Bottom line: A solid pick for anyone with one keg who wants a like-for-like replacement without extra features.

View on Amazon

CGA-320 Beer Regulator with Safety Valve, dual output

CGA-320 Beer Regulator, 0-55PSI Working Pressure, with Safety Valve, 5/16" Barb Outlet, for Home Brewing Y-Shaped CO2 Regulator for Kegerator, Dual Output Keg Regulator

CGA-320 Beer Regulator, 0-55PSI Working Pressure, with Safety Valve, 5/16" Barb Outlet, for Home Brewing Y-Shaped CO2 Regulator for Kegerator, Dual Output Keg Regulator

View on Amazon

Best for: Two-tap or two-keg setups that share one CO2 tank.

The Y-shaped body splits one tank supply into two outputs, which suits builds with a second keg or a split line to two taps. The listing highlights a safety valve, which is useful if a fitting fails under pressure.

Key specs

  • Working pressure: 0-55 psi
  • Outlet: 5/16″ barb
  • Dual output (Y-shaped)
  • Built-in safety valve

Pros

  • Two outputs from one tank reduce the number of regulators you need
  • The safety valve adds protection against over-pressure
  • Same 5/16″ barb as the single-output model, so line connections stay consistent

Cons

  • Both outputs share one pressure setting, so two kegs with different serving pressures need separate handling
  • Owners often mention that dual-output bodies take a little extra care when tightening fittings

Bottom line: The right choice for a two-keg kegerator where both lines serve similar beers at similar pressure.

View on Amazon

CO2 Tank Regulator with 0-60 PSI working pressure, triple output

CO2 Tank Regulator with 0-60 PSI Working Pressure & 0-3000 PSI Tank Pressure for Draft Beer Homebrew Keg System Triple Output CO2 Regulator for Kegerator, CGA-320 3 Way Keg Regulator

CO2 Tank Regulator with 0-60 PSI Working Pressure & 0-3000 PSI Tank Pressure for Draft Beer Homebrew Keg System Triple Output CO2 Regulator for Kegerator, CGA-320 3 Way Keg Regulator

View on Amazon

Best for: Multi-keg systems or builds with three or more lines.

If your kegerator feeds several taps or you are building a larger home bar, a triple-output regulator reduces clutter and keeps one gauge in view. It is also useful for brewers who want spare capacity without buying another regulator later.

Key specs

  • Working pressure: 0-60 psi
  • Tank pressure gauge: 0-3000 psi
  • Triple output
  • CGA-320 tank connection

Pros

  • Three outputs suit multi-keg and multi-tap builds
  • The 0-60 psi working range allows a little more headroom than 0-55 psi models
  • Tank gauge range is clearly marked for monitoring CO2 levels

Cons

  • Three outputs mean more potential leak points, so every fitting needs a check after installation
  • Overkill for a single-keg kegerator, where a simpler regulator is easier to troubleshoot

Bottom line: Best for builders running several kegs who want to consolidate regulation under one body.

View on Amazon

0-60 PSI CO2 Tank Pressure Regulator, single output CGA-320

0-60 PSI Working Pressure & 0-3000 PSI Tank Pressure, CO2 Tank Pressure Regulator for Homebrewing CO2 Regulator Single Output CGA-320 Keg Regulator Beer Regulator

0-60 PSI Working Pressure & 0-3000 PSI Tank Pressure, CO2 Tank Pressure Regulator for Homebrewing CO2 Regulator Single Output CGA-320 Keg Regulator Beer Regulator

View on Amazon

Best for: Budget-minded single-keg users who want the wider 0-60 psi range without paying for extra outputs.

This model keeps the design simple: one outlet, a CGA-320 connection and a pressure range that covers common draft serving pressures. It is a practical choice for a first kegerator build or a spare regulator for the garage.

Key specs

  • Working pressure: 0-60 psi
  • Tank pressure: 0-3000 psi
  • Single output
  • CGA-320 connection

Pros

  • Single output keeps the design uncomplicated
  • The 0-60 psi range gives extra room above typical serving pressures
  • Good match for a spare or backup regulator

Cons

  • No second output for future expansion
  • As with any low-cost regulator, owners often recommend a leak check with soapy water after installation

Bottom line: A sensible budget pick for one keg, especially if you want a backup on hand.

View on Amazon

Buying Guide

Confirm the tank connection (CGA-320)

Most US home brewing CO2 cylinders use the CGA-320 fitting. Check the stamp or label on your tank and the thread on the regulator before you order. A regulator with the wrong thread will not seal, and forcing it can damage the tank valve.

Good picks for this: Keg regulator with 0-55 psi working pressure, single output; CGA-320 Beer Regulator with Safety Valve

Working pressure range

Check the stated working pressure. A range of 0-55 psi or 0-60 psi covers the serving pressures most draft beer uses. What matters more is that you can dial in a precise, low setting, since many beers are served between roughly 8 and 14 psi depending on temperature and carbonation level.

Good picks for this: 0-60 PSI CO2 Tank Pressure Regulator; CO2 Tank Regulator with 0-60 PSI working pressure

Number of outputs

Count your kegs and taps before choosing. A single-output regulator suits one keg. Dual and triple-output bodies let one tank feed several lines, but every extra outlet is another fitting that can leak. Buy only as many outputs as you will use now, plus perhaps one for expansion.

Good picks for this: CGA-320 Beer Regulator with Safety Valve; CO2 Tank Regulator with 0-60 PSI working pressure

Safety features

A safety valve releases pressure if the regulator or downstream line is overpressured. Look for a listed safety valve, especially on dual or triple-output designs where one failure can affect several lines. The US Consumer Product Safety Commission publishes general guidance on pressurized equipment at cpsc.gov.

Good picks for this: CGA-320 Beer Regulator with Safety Valve

Gauge readability

You need two readings: tank pressure and working (outlet) pressure. Clear, well-marked gauges make it easier to see when your tank is running low and to set serving pressure accurately. Owners often report that small, hard-to-read dials are the first thing that frustrates them.

Good picks for this: 0-60 PSI CO2 Tank Pressure Regulator; Keg regulator with 0-55 psi working pressure

Barb size and line compatibility

Most kegerator builds use 3/16″ or 5/16″ beer line. Confirm that the regulator’s outlet barb matches the inside diameter of your line. A barb that is too small will let line slip off under pressure, while one that is too large will not fit the hose at all.

Good picks for this: Keg regulator with 0-55 psi working pressure, single output; CO2 Tank Regulator with 0-60 PSI working pressure

Durability and care

Regulators live on a pressurized system that gets moved, bumped and occasionally left connected through temperature swings. Brass bodies and solid fittings tend to hold up better than thin plastic parts. After every installation or tank change, check all connections with a little soapy water and watch for bubbles. Store the tank upright and secured, and keep the regulator capped when it is not in use.

Good picks for this: CGA-320 Beer Regulator with Safety Valve; 0-60 PSI CO2 Tank Pressure Regulator

FAQ

Why did my kegerator regulator stop working?

The most common causes are an empty or nearly empty CO2 tank, a leak at a fitting, a damaged diaphragm or seat inside the regulator, or a gauge that has drifted. Start by checking the tank gauge, then listen for a hiss and spray soapy water on each connection. If the regulator still will not hold pressure after a new tank and tight fittings, replace it.

How do I know if my regulator is leaking?

Turn off the gas at the tank, set the regulator to a moderate pressure, and close the outlet. Watch the gauge for several minutes. If the reading falls steadily, there is a leak somewhere in the system. Spray soapy water on each fitting; bubbles mark the source.

Can a regulator cause my beer to foam?

Yes. If the outlet pressure is set too high for the beer’s temperature and carbonation level, the beer can overcarbonate and pour foamy. Lowering the working pressure is usually the first adjustment to try. For more detail on foam issues, see Too Much Foam in Kegerator: 6 Causes and Fixes That Work.

What working pressure should I set?

Serving pressure depends on beer style, temperature and carbonation target. Many home setups serve beer in a range that sits roughly between 8 and 14 psi. A dedicated CO2 pressure guide can help you choose the right number; see What Should CO2 Pressure Be on Kegerator? 4 Best Regulators Compared (2026).

Do I need a single-gauge or dual-gauge regulator?

A dual-gauge regulator shows both tank pressure and outlet pressure at once, which makes it easier to tune serving pressure and spot a dropping tank. A single-gauge model shows only outlet pressure and is simpler. Most home brewers find dual gauges more useful. For setup steps, see How to Set Up Kegerator Regulator (2026): Single-Gauge vs Dual-Gauge Regulators.

Is a safety valve necessary?

A safety valve is a useful backup, especially on multi-output regulators where one failure can affect several lines. It does not replace careful setup, but it adds a margin of protection if something goes wrong.

Should I consult a professional about CO2 systems?

Compressed gas equipment carries real risk. If you are unsure about connections, tank handling or whether a regulator is rated for your tank, consult a qualified professional or your local gas supplier before proceeding.

My kegerator is not cooling as well as it should. Is that the regulator?

Usually not. Temperature problems usually come from the cooling system, not the regulator. If the beer is warm, check the thermostat and airflow first. See Kegerator Not Getting Cold? 6 Causes and Fixes That Work for troubleshooting steps.

Conclusion

A failing kegerator regulator is usually an easy repair once you match the right part to your setup. For a single keg and a like-for-like swap, the single-output keg regulator with 0-55 psi working pressure is the most straightforward choice. Two-keg builds will do better with the dual-output regulator with safety valve, while larger multi-line systems suit the triple-output model. The 0-60 psi single-output unit is a sensible budget pick for a first build or a backup. Before you install any of them, confirm the CGA-320 thread, check every fitting for leaks and, when in doubt, ask a professional.

Sources

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our home brewing guides, checking product details against manufacturer specifications and owner feedback.