Updated November 2026
An Edgestar kegerator that is not cooling usually has a simple cause you can find in under an hour. This guide walks you through the checks in order, from the thermostat setting to the condenser coils, so you can get the cabinet back to serving temperature and keep your beer properly chilled.
Check the Thermostat and Power First
Start with the controls before you touch anything inside the cabinet. Many kegerators are simply set warmer than the owner remembers, or the thermostat was bumped during cleaning. Turn the dial to a colder setting and confirm the compressor starts within a few minutes. If you hear nothing at all, check that the unit is plugged into a working outlet and that the cord is not damaged. Some owners find a tripped GFCI outlet is the real problem.
Shopping for one? See our guide: 6 Best Edgestar Dual Tap Kegerator Options for Home Bars (2026).
If the compressor runs but the temperature stays high, the thermostat sensor may have come loose from its mount. Keep in mind that if you are weighing whether to adjust the setpoint or replace a part, the approach in Edgestar Kegerator Temperature Adjustment (2026): Which Should You Choose? covers the tradeoffs.
Inspect Airflow and Ventilation
A kegerator needs space to shed heat from the back or underside of the cabinet. Pull the unit away from the wall and make sure nothing is blocking the vents. Heat trapped behind the cabinet forces the compressor to work harder and can keep the interior from reaching setpoint.
- Leave at least several inches of clearance at the back and sides, or follow the clearance specified in your owner’s manual.
- Keep the unit out of direct sunlight and away from ovens, radiators and dishwashers.
- Make sure any ventilation grille is clean and unobstructed.
Clean the Condenser Coils and Check the Door Seal
Dust and pet hair on the condenser coils insulate them from the surrounding air, so heat cannot escape efficiently. Unplug the unit, then vacuum the coils with a brush attachment. Do this every few months in a dusty garage or basement and you will avoid a lot of trouble.
Next, inspect the door gasket. Close the door on a sheet of paper. If the paper slides out easily anywhere around the frame, the seal has failed and warm air is getting in. Clean the gasket with warm water and mild soap, and replace it if it is cracked or flattened. Also confirm the door is fully latched, since a door left ajar even slightly can keep the cabinet from cooling.
Look at Load, Temperature Gain and the Compressor
Recently loaded kegs add heat, so a warm cabinet right after a restock is not always a fault. Give the unit several hours to pull the temperature down. Avoid loading room-temperature kegs and opening the door repeatedly during this time.
If the cabinet still will not cool after the coils are clean, the seal is good and airflow is clear, the compressor or refrigeration system may be failing. Stop there and contact Edgestar or a qualified appliance technician. Do not attempt to open or recharge the sealed refrigeration circuit yourself.
Common Mistakes
- Assuming the unit is broken when the thermostat was simply set too warm.
- Pushing the kegerator tight against a wall, which traps heat.
- Ignoring dusty condenser coils until the compressor runs constantly.
- Opening the door often during the first hours after loading kegs.
- Using an unrated extension cord, which can cause voltage drop and poor performance.
Recommended Gear
- Refrigerator thermometer: A standalone thermometer lets you confirm the real interior temperature instead of relying on the dial. View on Amazon
- Soft condenser brush or vacuum brush attachment: Helps you clean coils without bending the fins. View on Amazon
- Replacement door gasket: Useful if the seal has failed and the paper test shows air leaking at the frame. View on Amazon
FAQ
Why is my Edgestar kegerator running but not cold?
Running without cooling usually points to restricted airflow, dirty condenser coils or a door seal that lets warm air in. Clean the coils and check the gasket first. If the problem persists, the refrigeration system may need professional service.
How long should it take to cool down after loading kegs?
Allow several hours for the cabinet to return to setpoint after a restock, especially if the kegs were warm. Frequent door openings will extend that time.
Can I fix a kegerator that will not cool myself?
You can safely handle the basics: setting the thermostat, clearing airflow, cleaning coils and replacing a gasket. Sealed refrigerant work should be left to a qualified technician, and you should consult a professional before attempting any repair beyond these checks.
Conclusion
Most Edgestar kegerator cooling problems come down to settings, airflow, dirty coils or a leaking door seal, and you can check all of them yourself. Work through the list in order and you will usually find the cause quickly. If the compressor and sealed system are the issue, get a qualified technician involved early to protect your beer and your unit.
